Description
Stronger Grip. Lower Heat. Longer Life.
Bambu Cool Plate SuperTack Pro
The Bambu SuperTack Pro is designed to deliver powerful first-layer adhesion for PLA and PETG while using lower heatbed temperatures.
Its upgraded coating helps reduce warping, improve print reliability and extend the usable life of the build plate.
Longer Service Life
The Pro coating is designed for improved durability and lower adhesion loss over repeated printing cycles.
Lower Bed Temperature
PLA and PETG can print at lower heatbed temperatures than on the previous SuperTack plate.
Strong First Layer
High surface grip reduces lifting, failed first layers and warping on large parts.
Smooth Matte Finish
The coating creates a smooth, natural-looking finish on the bottom surface of the model.
Upgraded Surface Technology
What Makes SuperTack Pro Different?
SuperTack Pro improves the original low-temperature adhesion concept with a more durable coating, better scratch resistance and lower required bed temperatures.
As a result, users can achieve dependable first layers while reducing energy use and extending the working life of the plate.
- 25% longer stated lifespan
- 10% lower operating temperature
- Improved resistance to scratches
- Strong adhesion for PLA and PETG
- Less than 15% adhesion loss after 300 stated test prints
Say Goodbye to Failed First Layers
Ultra-Strong Adhesion for PLA and PETG
The SuperTack Pro coating holds PLA and PETG securely, even at relatively low heatbed temperatures.
Strong grip helps prevent corners from lifting and reduces the risk of wide or tall objects warping during printing.
It can also help maintain adhesion when a model has a limited contact area or an awkward first-layer shape.
Better Stability
Reduces Warping on Large Prints
Large objects place more stress on the first layer as the printed material cools and contracts.
SuperTack Pro provides a strong foundation across the full contact area. Therefore, wide models, panels and long parts are less likely to lift at the corners.
Actual results still depend on the filament, model geometry, room conditions and slicer settings.
Long-Lasting Performance
Built for Repeated Printing
The upgraded coating is designed to retain its adhesive properties after extensive use.
In the manufacturer’s stated test using PLA Basic on an A1 printer, adhesion loss remained below 15% after 300 prints.
A longer service life can reduce replacement frequency, material waste and overall operating cost.
Natural-Looking First Layer
Smooth and Matte Bottom Finish
The SuperTack Pro coating creates a smooth, low-gloss texture on the bottom of printed parts.
This allows the first-layer surface to blend more naturally with the other walls of the model.
It is especially useful for display parts, enclosures, decorative models and products where the underside remains visible.
Lower Heatbed Temperatures
SuperTack Pro can maintain strong adhesion at lower heatbed temperatures than the original SuperTack plate.
Consequently, the printer requires less energy to heat the bed and may reach the target temperature faster.
| Material | SuperTack | SuperTack Pro |
|---|---|---|
| PLA | 45°C | 40°C |
| PETG | 70°C | 60°C |
Safe Model Removal
How to Remove Prints Without Damaging the Coating
- Allow the print and plate to cool.
- Use the scraper supplied with the printer to lift one edge gently.
- Pry the model away slowly without digging into the coating.
- If the model remains tightly attached, heat the plate to approximately 50°C and try again carefully.
The SuperTack Pro surface is relatively soft. Avoid sharp scraping angles and excessive force.
Important Material and Care Information
- Do not print TPU on SuperTack Pro because it can damage the surface.
- Bambu PLA Silk+ is supported under the manufacturer’s stated guidance.
- Other PLA Silk materials may bond too strongly and can damage the print or plate.
- Do not use acetone or other organic solvents.
- Clean only when needed, using water and ordinary dishwashing detergent.
- Use the scraper carefully because the coating is soft.
- Select the correct printer size before ordering.
Cleaning and Maintenance
SuperTack Pro normally provides strong adhesion without frequent cleaning or additional glue.
If dirt, dust or fingerprints build up, wash the plate gently with water and dishwashing detergent.
- Use clean water and ordinary dish soap
- Use a soft sponge
- Rinse thoroughly
- Allow the plate to dry fully
- Avoid touching the printing surface afterwards
- Never use acetone or organic solvents
Simple Installation
Install the Plate in Two Steps
- Align the plate with the locating points on the printer platform, keeping the plate name facing you.
- Lower the plate carefully and allow it to attach to the magnetic heatbed.
Confirm that the plate sits flat and is correctly aligned before printing.
Select the correct SuperTack Pro plate profile in Bambu Studio when available.
Bambu Cool Plate SuperTack Pro Specifications
| Specification | 256 × 256 mm | 350 × 320 mm | 330 × 320 mm |
|---|---|---|---|
| Material | Specially designed coating and spring-steel plate | ||
| Coating Thickness | 0.05 mm | ||
| Steel Plate Thickness | 0.4 mm | ||
| Surface Temperature Resistance | Up to 120°C | ||
| Compatible Printers | X1C, P1P, P1S, A1, P2S and X2D | H2D and H2S | H2C and A2L |
| Packaging Size | 315 × 295 × 15 mm | 393 × 380 × 15 mm | 393 × 380 × 15 mm |
| Packaging Weight | 0.22 kg | 0.48 kg | 0.46 kg |
Product Summary
The Bambu Cool Plate SuperTack Pro is a low-temperature magnetic build plate designed primarily for PLA and PETG. Its upgraded coating offers strong first-layer adhesion, reduced warping, improved scratch resistance, longer stated service life and a smooth matte finish on printed parts.
Bambu SuperTack Pro in Cyprus
The Bambu Cool Plate SuperTack Pro is available from The 3D Factory with delivery across Nicosia, Limassol, Larnaca, Paphos and Famagusta.
We also supply compatible Bambu Lab printers, PLA and PETG filament, replacement hotends, build plates and related accessories.
Related Products and Official Resources
Frequently Asked Questions
Is SuperTack Pro compatible with the Bambu Lab A1 Mini?
The specifications supplied for this product do not include a 180 × 180 mm A1 Mini version. Confirm the physical dimensions and official compatibility before ordering.
Which materials work with SuperTack Pro?
It is primarily designed for PLA and PETG. TPU must not be used because it can damage the coating.
Does SuperTack Pro require glue?
No glue is normally required for supported PLA and PETG printing.
What heatbed temperature should I use?
The manufacturer lists approximately 40°C for PLA and 60°C for PETG as comparison values for SuperTack Pro. Adjust settings according to the filament and model.
Can I print TPU on SuperTack Pro?
No. TPU can bond too strongly and damage the build-plate coating.
How should I clean the plate?
Use water and ordinary dishwashing detergent when heavy dirt appears. Do not use acetone or other organic solvents.
How should I remove a strongly attached print?
Lift one edge gently with the printer scraper. If necessary, heat the plate to around 50°C and remove the model carefully.
Is Bambu SuperTack Pro available in Cyprus?
Yes. Bambu Cool Plate SuperTack Pro is available from The 3D Factory with local support and delivery across Cyprus.
